Installation ManualCon TROLL®PRO Installation ManualInformation subject to change without notice. In-Situ, In-Situ logo, Baro Merge, BaroTROLL, HERMIT
10Figure 3.3 Controller dimensions with lid openFigure 3.4 Side view dimensional drawings
11Pole Mounting1. Remove the 4 nuts and 4 screws from the mounting kit.2. With the enclosure open, drop 1 nut into each drilled corner of the box.3. U
12Figure 3.6 Attaching the mounting bracketsFigure 3.7 Back and side view of pole-mounted controllerWall Mounting Using Mounting TabsThe optional moun
13Wall Mounting with User-supplied HardwareYou can supply your own mounting hardware and attach the controller to a wall. Use ascrew that is best suit
14DIN Rail Mounting the EnclosureEach rail mount clip is secured to the enclosure with a supplied #6 screw.1. With the enclosure open, drop 1 screw in
15Do not over tighten.3. Inside the enclosure, place the lock nut, concave-side-down, over the threaded endof the plug or dome connector and tighten w
16Electrical ConnectionsDanger—Only properly trained and qualified personnel should install thecontroller described in this manual. This instrument sh
17l The cable does not slide or move after the connectors are tightened.l Sufficient cable has been threaded through the connector so that secure wiri
18Figure 4.2 AC circuit board and terminal connections1. Disconnect power to the controller.2. Use a Phillips screwdriver to remove the controller lid
19Danger—Ne pas connecter des circuits basse tension (moins de 50 V) auxbornes de connexion sur la carte électronique de secteur (courant alternatif)!
2Copyright © 2009-2013 by In-Situ Inc. All rights reserved.This document contains proprietary information which is protected by copyright. No partof t
20Input/Output ConnectionsThe Input/Output board is shown in Figure 5.1 . It is located inside the enclosure on theleft side. Refer to the individual
211. Disconnect power to the instrument.2. Use a Phillips screwdriver to remove the controller lid.3. Connect the stripped-and-tinned PLC wires to the
22If you want to use RuggedCable with twist-lock connectors, ordera short length of stripped-and-tinned RuggedCable with a maleconnector. This can be
23Do not ground the device at both ends of the cable.5. Replace the controller lid and tighten screws.6. Reconnect power to the device.
24Relay Connections on the I/O BoardPlease note that the DC and AC models have different types of relays available. Allrelay connections are unpowered
25Optional Battery BoxOverview of Battery Box KitThe optional external battery box kit is designed to power the DC-L Model Con TROLLPRO via battery. I
264. Thread the opposite end of the cable through the dome connector and into thebattery enclosure.5. Firmly tighten the dome connector with a wrench.
27MaintenanceDanger—Only properly trained and qualified personnel should install the ConTROLL PRO described in this manual. This instrument should be
28SpecificationsOverviewThe Con TROLL PRO has an easy-to-use interface that supports 2 probes. AC and DCversions are available.l The DC version is low
29Declaration of Conformity
3Table of Contents1 Safety5Hazard Symbols that Appear in the Manual 5Precautionary Labels that many Appear on the Product 52 Overview6Available Models
4Overview 28Specifications 289 Declaration of Conformity29
5SafetyPlease read this manual before unpacking or installing any part of this system.Hazard Symbols that Appear in the ManualDanger—Indicates a hazar
6OverviewAll Con TROLL PRO models contain the following items.l NEMA 4X ratedl Robust keypad and display windowl Easy-to-use controller softwareFor a
7Box ContentsRemove the controller from the shipping box. The shipping box should contain thefollowing items.l Controller (1)l Controller plugs (5)l D
8Mounting the ControllerDanger—Only properly trained and qualified personnel should install thecontroller described in this manual. This instrument sh
9Mounting OptionsController DimensionsFigure 3.2 shows the controller dimensions with the lid closed.Figure 3.3 shows the dimensions of the controller
Comments to this Manuals